WAI widens merchandise programme

Published:  09 April, 2018

WAIglobal has introduced a new range of branded merchandise. The WAI-branded selection includes a mobile phone power bank, mouse pad, car charger, enamel pin, notebook, drinks tumbler, international socket adapter, USB flash drive, USB power bank, USB phone adapter and charging cable, alternator air freshener, emergency jump starter, drinks coaster and, finally, a non-abrasive microfibre cloth. The new merchandise is intended to enable its parts distributors to share the brand’s message on a wider scale and ultimately drive through sales of WAI’s extensive aftermarket range.
www.waiglobal.com

Related Articles

  • WAI widens merchandise programme  

    WAIglobal has introduced a new range of branded merchandise. The WAI-branded selection includes a mobile phone power bank, mouse pad, car charger, enamel pin, notebook, drinks tumbler, international socket adapter, USB flash drive, USB power bank, USB phone adapter and charging cable, alternator air freshener, emergency jump starter, drinks coaster and, finally, a non-abrasive microfibre cloth. The new merchandise is intended to enable its parts distributors to share the brand’s message on a wider scale and ultimately drive through sales of WAI’s extensive aftermarket range.
    www.waiglobal.com

  • WAI product arrives at Marathon branches 

    WAI product has begun leaving Bognor Regis and arriving at Marathon Warehouse Distribution’s national distribution centre in Redditch and a 14-branch network throughout the UK.

  • Issues of rotation 

    I received a phone call from another garage: 'We've seen you in the Top Technician magazine and are wondering if you would be interested in looking at an ABS fault for us?' The call went along the usual lines, can the symptoms be recreated? What is the repair history? The vehicle was booked in for me to take a look.

    The car in question was a 2011 Honda
    CR-V, which had been taken as a trade in at a local garage, the fault only occurred after around 50-70 miles of driving, at which point the dash lights up with various warning lights. The vehicle had been prepped and sold to its new owner unaware a fault was present.

    Fault-finding
    After only a few days the fault occurred and the vehicle returned to the garage. They had scan checked the vehicle and the fault code ‘14-1- Left Front Wheel Speed Sensor Failure’ was retrieved. On their visual inspection, it was obvious a new ABS sensor had already been fitted to the N/S/F and clearly not fixed the fault. Was this the reason the vehicle had been traded in? They fitted another ABS sensor to the N/S/F and an extended road test was carried out. The fault reoccurred. This is when I received the phone call; the garage was now suspecting a control unit fault.
        
    My first job was to carry out a visual inspection for anything that was obviously wrong and had possibly been over looked: correct tyre sizes, tyre pressures, tyre tread and excessive wheel bearing play. All appeared ok. The ABS sensors fitted to this vehicle are termed 'Active' meaning they have integrated electronic and are supplied with a voltage from the ABS control unit to operate. The pulse wheel is integrated into the wheel bearing, which on this vehicle makes it not possible to carry out a visual inspection without stripping the hub.

    Endurance testing
    With the vehicle scan checked, all codes recorded and cleared, it was time for the road test. Viewing the live data from all the sensors, they were showing the correct wheel speed readings with no error visible on the N/S/F. The road test was always going to be a long one, fortunately at around 30 miles, the dash lit up with the ABS light and lights for other associated systems; the fault had occurred. On returning to the workshop, the vehicle was rescanned, fault code '14-4 - Left Front Wheel Speed Sensor Failure’ was again present. Again using the live data the sensor was still showing the wheel speed the same as the other three, so whatever was causing the fault was either occurring intermittently or there was not enough detail in the scan tool live data graph display to see the fault. It was time to test the wiring and the sensor output signal for any clues.
        
    Using the oscilloscope, the voltage supply and the ground wire were tested and were good at the time of test. I connected the test lead to the power supply wire and using the AC voltage set to 1V revealed the sensors square wave signal. Then rotating the wheel by hand and comparing the sensors output to one of the other ABS Sensors, again all appeared to be fine. A closer look at the signal was required, zooming in on the signal capture to reveal more detail; it became easier to see something was not quite right with the signal generated by the sensor when the wheel was rotated. With the voltage of the signal remaining constant, a good earth wire and the wheel rotated at a constant speed the signal width became smaller, effectively reporting a faster speed at that instant, not consistent with the actual rotational speed of the wheel. It was difficult to see the error, zooming out of the capture to show more time across the screen it could be seen that this appeared in the signal at regular intervals, although not visible all the time because it was such a slight difference. Using the cursors to measure between the irregular output and counting the oscillations, it was clear that it occurred at exactly the same interval every time. It had to be a physical fault on the pulse wheel.
        
    This meant a new wheel bearing was required. The vehicle was returned to the garage as they wanted to complete the repair, a new wheel bearing was fitted and extended road testing confirmed the vehicle was now fixed.

  • Ben shines spotlight on workplace bullying  

    Ben has launched new web resources to help people cope with bullying in the workplace, just in time for National Anti-Bullying  Week, which is taking place this week (12-16 November).

  • New alternator from AS-PL  

    AS-PL has introduced a new product – an alternator with the index number A3374S, which is a product of the AS brand. The new product belongs to the Standard line. The product can be used in Citroën AX, Citroën BX, Citroën C15 and Peugeot 205, Peugeot 309 and Peugeot 405. AS-PL Sp. z o.o. offers more than 15,000 different products with a total of almost 200,000 reference numbers. A wide selection of original products are divided into three product lines: Economy, Standard and Premium. The offered products include parts and components for passenger cars, lorries, agricultural machines, boats, motorcycles, and for the industrial market.
    https://en.as-pl.com/

Most read content


Search

Sign Up

For the latest news and updates from Aftermarket Magazine.


Poll

Where should the next Automechanika show be held?



Facebook


©DFA Media 1999-2018